A Kenmore washer that will not spin has lost something between the motor and the basket, or something has told the washer it is not safe to spin. That covers everything from a small drive part to a machine that is worn out underneath, and from the front they look the same.
We went back through our last 22 Kenmore washer calls where the complaint was no spin. Only one owner saw a code on the display, an OL, so on nearly all of these there was no code to go on at all. Here is what our technician actually found.
What no-spin actually was, 22 times
- Three of 22 — the motor coupler. The part that connects the motor to the transmission. All three were repaired with a new coupler, and one of them got new agitator dogs at the same time.
- Three of 22 — the clutch. Two were repaired with a new clutch and agitator dogs. The third had a rusted frame as well, and was not worth the money.
- Three of 22 — the hub or the shaft. One needed a new basket hub. One had a corroded transmission shaft that cleaned up and ran. One had a stripped hub and a broken transmission bolt, and was not economical.
- Four of 22 — sensors and switches. A failed hall sensor, a speed sensor that needed recalibrating after a stored basket speed fault, a pressure sensor plus capacitors on the control, and a lid switch that only needed adjusting. All four were repaired.
- Six of 22 — bearings, tub or transmission. Two failed tub bearings, one transmission and bearings, one transmission and tub, one set of motor bearings, and one broken wash tub with no part available. All six ended with a replacement washer.
- Three of 22 — one each. A failed drain pump, a clogged inlet screen, and a drive motor that would not reverse. The first two were repaired; the motor job was not worth it.
So the drive parts, the couplers and clutches together, were six of 22, and all three couplers and two of the three clutches were fixed. That is the good news. The six bearing, tub and transmission failures are the other half of the story, and it is better to know that going in.
What you can safely check first
Unplug the washer before you touch anything, and shut the water off at the valves if you are going to look at the hoses. Then:
Is there water left in the tub? A washer that has not drained will not spin. One of our 22 was a failed drain pump. You cannot fix that from the outside, but it tells your technician where to start.
Does the lid close fully and firmly? On a top-loader the washer will not spin if it does not see the lid shut. One of ours was a lid switch out of adjustment, and adjusting it was the whole repair.
Are the inlet screens clear? With the washer unplugged and both water valves off, the fill hoses unscrew from the back and there is a small screen where each one connects. One of our 22 ended with a new inlet screen.
Is the load reasonable? Take out one heavy item, spread the rest around and try a drain and spin. It costs nothing to rule out.
The honest odds: the things an owner can see from the outside lined up with two of our 22 jobs, the lid switch and the clogged inlet screen, and even those took a technician to fix. Most of these needed a part inside the cabinet. Do not open the cabinet with the washer plugged in.
The observation that separates cheap from expensive
Before you call, watch one cycle and note exactly what the washer does and does not do. It helps narrow things down.
If nothing moves at all, no agitating and no spinning, that points toward the drive between motor and transmission. One of our coupler jobs came in as exactly that, not agitating or spinning, and a new coupler fixed it.
If it agitates but the basket will not spin, the clutch and hub are where our technician looks first. Those were repaired more often than not on these jobs.
Here is the hard part. On all six of the bearing, tub and transmission jobs, the complaint was the same plain “not spinning” that came in on the cheap repairs. Nothing the owners reported set them apart. The difference only showed up once our technician got inside and looked at the bearings, tub and transmission. That is why a diagnosis comes before any part gets ordered, and why buying a coupler or clutch on a guess can mean paying for a part on a washer that was never going to be worth saving.
Bad bearings are not automatically the end, though. On the drain pump job the drum bearings were replaced at the same time and that washer was repaired. It depends on the rest of the machine.
When we tell you it is not worth it
Besides those six, three more went the same way: the stripped hub with the broken transmission bolt, the drive motor that would not reverse, and the clutch on the rusted frame. On the broken wash tub, the part simply was not available. We would rather tell you that after the diagnosis than after you have paid for parts.
Kenmore is not one washer
Kenmore washers have been built by more than one manufacturer, and the first three digits of the model number tell you which. Most of our 22 shared one prefix, but a few were Kenmores from a different maker, with different parts inside. Advice written for one Kenmore can send you after the wrong part on another, so have the full model number handy when you call.
The same goes for that OL code. On our one job with it, the cause was a corroded transmission shaft, and cleaning it got the washer spinning again. One job is not a rule, so do not treat a search result for OL as a parts list.
What it costs
The service call is $167 for a top-loader and $187 for a front-loader, a little more outside the regular route, and it comes off the repair when you go ahead. You get a flat-rate quote before any work starts, and labor is covered for six months.
Kenmore still will not spin? Request service online any time, or call or text (330) 915-7222.