A Whirlpool range that will not heat in the oven has lost the part that turns electricity or gas into heat, or the part that tells it when to make heat. The cooktop may work perfectly. The oven seems to be on, and it sits there cold.
The symptom looks the same on every range. What actually failed depends a great deal on whether your range runs on gas or electric. That one fact settles much of the guesswork before anyone opens a panel.
What it actually was, 21 times
- Nine of 21 — the igniter on a gas range. That count combines four written up as a failed oven igniter, three as a failed bake igniter, one as a failed bake ignitor and one as a weak bake igniter. Same part, different wording. A new igniter got the oven heating every time.
- Six of 21 — the bake element on an electric range. The element in the floor of the oven. A new element fixed all six.
- Three of 21 — the main control board. One was rebuilt, one was replaced, and on one the board was no longer available, so the range was not worth repairing.
- One — burnt wiring at the terminal block. New terminal block and new connectors on the burnt wires.
- One — the oven temperature sensor.
- One — no problem found. Our technician tested the element and ran the oven, and it would not fail while we were there.
Put plainly: on a gas Whirlpool, think igniter. On an electric one, think bake element. The control board came in third. Those three parts covered eighteen of our 21 calls.
Gas or electric is the first question
This catches people who search the symptom before they look at the range. Most of what you will read about a cold oven is written about one kind or the other, and the fix for a gas oven has nothing to do with the fix for an electric one. An electric oven has no igniter. A gas oven has no electric bake element. Know which you own before you read any further, ours included.
What you can safely check first
Start with the breaker. An electric range sits on a double breaker, and if one side trips, parts of the range can still look alive while the oven does nothing. Reset it once. If it trips again, leave it off and call.
On an electric range, with the oven completely cool and the range unplugged or its breaker off, look at the bake element on the oven floor. A break, a blister or a burnt spot on the element tells you a lot. You are only looking. Do not try to remove it.
On a gas range, set the oven to bake and watch through the window or the slot in the oven floor. You are looking for the igniter to glow and then for flame. Do not take the floor out and do not touch anything on the gas side. If you smell gas at any point, do not try to light anything, do not switch anything on or off, and do not handle the range or its gas line. Get everyone out of the house and call your gas utility from outside.
The honest odds: these checks rarely fix the oven. Of our 21 calls, every one but the no-problem-found visit came down to a failed part or damaged wiring. What the checks do is tell us which half of the range to bring parts for, and that saves you time.
The observation that separates the cheap fix from the expensive one
On a gas oven, the thing to watch for is an igniter that glows but never lights the burner. As a general rule, on gas ovens built this way the gas valve only opens once the igniter draws enough current. An igniter that has weakened can still glow, so it looks like it is working, yet never draw enough to open the valve. If you see a glow and no flame, that points hard at the igniter. On all nine of our igniter calls, a new igniter got the oven heating.
On an electric oven, the question is whether the element failed or the control stopped sending it power. From the front they look identical: a cold oven. Our technician tests the element itself. If it is open, it is the element. If the element tests good and the control is not powering it, the problem is upstream at the board, and a new element would not have fixed anything. That test is the difference between one of the most common repairs on this list and the most expensive one.
When it is the control board
Three of our calls landed here, and they went three different ways. One board was sent out and rebuilt, then reinstalled. One was replaced with a new board. On the third, the board was no longer available, and we told the owner straight that the range was not economical to repair. We would rather say that on the first visit than order something that does not exist.
Burnt wiring is not a DIY job
One range was not heating because the wires at the terminal block, where the power cord connects at the back, had burnt. We replaced the terminal block and the connectors on the damaged wires. If you smell burning from the back of the range or see scorching around the cord, turn the breaker off and leave it off. That is live electrical, and it needs a technician.
When the oven will not fail for us
One call ended with no problem found. Our technician tested the element and ran the oven, and it heated normally. An oven that quits only now and then is frustrating, but it is worth noting when it happens: right at startup, partway through a long bake, only at high temperatures. That detail is what lets us catch it the next time.
The service call
The service call is $167, a little more outside the regular route, and it comes off the repair when you go ahead. You get a flat-rate quote before any work starts, and labor is covered for six months.
Oven still cold? Request service online any time, or call or text (330) 915-7222.